795nm VCSEL for Rubidium Atomic Clocks and OPM Magnetometers

Atomic Timing · Rubidium Spectroscopy · OPM

795nm VCSEL for Rubidium Atomic Clocks and OPM Magnetometers

Rubidium-based atomic clocks and optically pumped magnetometers use precision optical sources to interact with the atomic D1 transition near 795nm. A suitable VCSEL can provide a compact, low-current single-mode source for vapor-cell optical systems.

Lumi offers a 795nm single-mode VCSEL with TO-46 and TO-39 package options and TEC-stabilized configurations. Its published specifications include 0.13mW typical output power, a maximum 100MHz spectral linewidth, minimum 20dB SMSR, minimum 15dB PER and minimum 3.4GHz FM modulation bandwidth.

The device is a laser-source component, not a complete frequency-locked atomic clock or magnetometer. Final suitability depends on the vapor cell, frequency-control method, optical power budget, polarization, thermal design and system validation.

795nm Rb D1Single-Mode VCSELTO-46 / TO-39TEC Option3.4GHz FM Bandwidth
Rubidium D1 Optical Source795 nm
VCSEL → Rb Vapor Cell → Optical SignalWAVELENGTH MATCHING · OPTICAL PUMPING · FREQUENCY CONTROL
795nm VCSEL Rb VAPOR CELL PD / CONTROL Atomic resonance interrogation Conceptual system diagram — not a complete Lumi module
Rb D1 · 794.98nmCPT ClockOPM MagnetometerTEC Stabilization
795nmTypical vacuum peak wavelength · Rubidium D1 region
0.13mWTypical optical output power at stated test conditions
≤100MHzMaximum spectral linewidth
≥3.4GHzMinimum FM modulation bandwidth
Application Overview

One 795nm Source, Two Precision Sensing Directions

Atomic clocks and optically pumped magnetometers both use alkali-metal vapor cells, but their system objectives and validation requirements are different. The optical source must be selected for the target transition and the complete instrument architecture.

01

Rubidium CPT Atomic Clocks

A 795nm laser addresses the rubidium D1 transition. In coherent population trapping (CPT) clock architectures, frequency-modulated optical sidebands interrogate the ground-state hyperfine resonance in a rubidium vapor cell.

Key requirements: D1 wavelength · RF modulation · frequency locking · thermal stability
02

Optically Pumped Magnetometers

An OPM uses polarized light to prepare and probe the atomic spin state of an alkali vapor. Changes in the atomic response are used to measure magnetic fields, with performance depending on optical, magnetic and thermal conditions.

Key requirements: stable polarization · low noise · magnetic compatibility · vapor-cell integration
03

Chip-Scale Quantum Sensors

Compact vapor-cell systems combine a laser source, cell, optics, photodetector, temperature control and electronics. Small VCSEL packages can support miniaturized optical-source architectures when device-level performance matches the design.

Key requirements: footprint · power budget · package · system calibration

Product positioning: Lumi currently publishes a 795nm VCSEL source. This page focuses on rubidium D1 applications. Cesium D1 systems near 894.6nm and rubidium D2 systems near 780.2nm require different wavelength configurations and are not represented as current Lumi products here.

Atomic Transition & Wavelength

Why 795nm Matters for Rubidium D1 Spectroscopy

Alkali-metal atomic systems use well-defined resonance transitions. The optical source wavelength must be compatible with the selected isotope, transition and frequency-control architecture.

Atomic SpeciesTransitionApproximate Vacuum WavelengthApplication ContextLumi Product Status
Rubidium (Rb)D1795nm (about 794.98nm)Rb CPT atomic clocks; Rb OPM magnetometers795nm VCSEL listed
Rubidium (Rb)D2780.2nmRubidium spectroscopy and selected optical-pumping systemsNo matching current product listed here
Cesium (Cs)D1894.6nmCs vapor-cell atomic clocks and OPM systemsNo matching current product listed here
Cesium (Cs)D2852.3nmCesium spectroscopy and selected atomic systems850nm product is not a substitute for a specified 852.3nm source

Wavelength selection note: nominal wavelength is only the starting point. Confirm the required isotope and hyperfine transition, actual operating temperature, current/temperature tuning range, frequency offset, linewidth, polarization and locking method. A nominal 795nm label does not by itself guarantee resonance with every rubidium setup.

Application 01 · Atomic Timing

795nm VCSEL for Rubidium CPT Atomic Clock Development

Compact rubidium clocks commonly use the D1 optical transition near 795nm. In a CPT architecture, two optical frequency components address the two ground-state hyperfine levels and create a narrow resonance used as a frequency reference.

How the 795nm Laser Is Used in a CPT Clock

A VCSEL can be frequency-modulated to generate optical sidebands. In a common 87Rb CPT arrangement, the modulation frequency is close to half the ground-state hyperfine splitting, around 3.417GHz, so the first-order sidebands are separated by approximately 6.834GHz.

  • 795nm optical carrier matched to the rubidium D1 region
  • RF current modulation or an external modulation stage
  • Rubidium vapor cell and magnetic-field environment
  • Photodetector to monitor transmitted optical intensity
  • Servo and frequency reference to stabilize the CPT resonance
  • Thermal control to maintain the laser's operating point

Why Lumi's 3.4GHz FM Specification Is Relevant

The product lists a minimum FM modulation bandwidth of 3.4GHz. This is close to the approximately 3.417GHz modulation frequency used in common 87Rb CPT clock architectures.

It makes the device a relevant candidate for engineering evaluation. It does not, by itself, guarantee the required modulation depth, sideband balance, CPT contrast, clock stability or locking performance.

Engineering distinction: FM modulation bandwidth is not the same as a guaranteed RF modulation response at every drive level. Verify modulation efficiency, RF impedance, bias conditions, sideband spectrum and the complete CPT signal with the intended driver and vapor cell.

Application 02 · Magnetic Field Sensing

795nm VCSEL for Rubidium Optically Pumped Magnetometers

Optically pumped magnetometers use light to prepare and interrogate atomic spin states in a vapor cell. A 795nm source can address the rubidium D1 transition in Rb-based OPM architectures.

Optical Source Requirements

  • Wavelength matched to the selected rubidium transition
  • Single-mode operation and suitable spectral characteristics
  • Stable polarization and adequate polarization extinction
  • Low intensity noise and low phase noise
  • Stable output under the intended thermal condition
  • Optical power matched to the vapor cell and optical path

Magnetic & Mechanical Integration

  • Package materials compatible with the sensor's magnetic environment
  • TEC and current-driver magnetic interference assessment
  • Low-noise current supply and grounding strategy
  • Magnetic shielding and vapor-cell placement
  • Optical alignment and polarization optics
  • Thermal and magnetic cross-sensitivity validation

Important package limitation: Lumi lists TO-46 and TO-39 package options and TEC-stabilized configurations, but the current product record does not confirm a non-magnetic package or magnetic-material screening. OPM customers should specify the magnetic environment and request package-material confirmation before design-in. Do not assume a standard TO-can is non-magnetic.

Lumi Product

795nm Single-Mode VCSEL Laser Diode with TEC Options

A TO-can VCSEL source for wavelength-sensitive optical systems, rubidium D1-line evaluation, precision spectroscopy and selected vapor-cell instrument development.

795nm VCSEL Laser Diode – TO-46 / TO-39

The device provides a typical vacuum peak wavelength of 795nm, typical output power of 0.13mW and typical threshold current of 0.75mA. Its spectral and modulation characteristics support evaluation in precision optical systems that require a compact single-mode VCSEL source.

  • Typical peak wavelength: 795nm
  • Maximum spectral linewidth: 100MHz
  • Minimum SMSR: 20dB
  • Minimum PER: 15dB
  • Minimum FM modulation bandwidth: 3.4GHz
  • TO-46 and TO-39 package options
  • TEC-stabilized configurations available

Product image status: the current WooCommerce product record does not yet contain an approved product image. The product-card image is hidden in this application section to avoid displaying a placeholder. Upload the official 795nm VCSEL photo to WooCommerce product ID 7325 when available.

Published Device Specifications

795nm VCSEL Technical Specifications

The values below follow the current Lumi product page. Typical, minimum and maximum values are kept distinct, together with the published test conditions.

ParameterSymbolValue TypeSpecificationUnit
Forward VoltageVFTypical1.8V
Output PowerΦTypical0.13mW
Threshold CurrentIthTypical0.75mA
Slope EfficiencySETypical0.21W/A
Single-Mode Suppression RatioSMSRMinimum20dB
Polarization Extinction RatioPERMinimum15dB
Peak Wavelength (Vacuum)λpeak-vMinimum794.76nm
Peak Wavelength (Vacuum)λpeak-vTypical795nm
Peak Wavelength (Vacuum)λpeak-vMaximum795.28nm
Spectral LinewidthΛlinewidthMaximum100MHz
FM Modulation BandwidthFmMinimum3.4GHz
Wavelength Temperature CoefficientTCλTypical0.055nm/K
Field of View at FWHMφx / φyTypical12 / 12°
Field of View at 1/e²φx / φyTypical20 / 20°

Reference operating conditions: Ta = 75°C, IF = 1.4mA and DC = 100% for the stated measurement conditions. The product page lists TEC-stabilized package configurations as available options. Confirm the exact package configuration and test conditions for the ordered part.

Laser Architecture Selection

795nm VCSEL vs DFB / DBR Lasers for Atomic Systems

VCSEL, DFB and DBR sources can all be used in precision optical systems. The correct choice depends on the optical power, spectral behavior, tuning range, modulation approach, package and instrument architecture.

Selection Factor795nm VCSEL795nm DFB / DBREngineering Consideration
Emission structureVertical-cavity, surface-emittingEdge-emitting with grating-based wavelength selectionDifferent cavity and optical-output architectures
Package directionCompact TO-can or bare die, depending on productTO-can or butterfly formats are commonChoose based on optical path and thermal integration
Output powerDevice- and aperture-dependent; Lumi 795nm product: 0.13mW typicalProduct-dependent; some commercial 795nm DFB/DBR sources offer higher powerCheck power delivered to the vapor cell after optical losses
Spectral linewidthDevice-specific; Lumi maximum 100MHzCan be specified at lower linewidth for selected modelsEvaluate free-running and locked linewidth separately
Frequency tuningCurrent and temperature behavior depend on the VCSEL designCurrent and temperature tuning depend on grating and cavity designCheck tuning range, mode-hop-free behavior and locking method
ModulationLumi specifies minimum 3.4GHz FM bandwidthDepends on model and RF/optical designCheck RF impedance, modulation depth and sideband spectrum
Potential fitCompact vapor-cell systems and selected CPT / OPM evaluationsPrecision spectroscopy and systems requiring other power or linewidth rangesChoose from system requirements, not architecture labels alone

Published literature lists commercial 795nm DFB/DBR alternatives with different power and linewidth specifications. The values are model-specific and are not a universal comparison between laser architectures. Review the actual datasheet and operating conditions before making a design decision.

Wavelength & Thermal Management

Why TEC Stabilization Matters in 795nm Rubidium Systems

The VCSEL wavelength changes with operating temperature. In a vapor-cell system, wavelength drift can move the laser away from the required atomic transition and affect the optical signal.

01

Temperature-Dependent Wavelength

Lumi specifies a typical wavelength temperature coefficient of 0.055nm/K. Temperature control should be considered when the optical source must operate near a defined rubidium resonance.

Published parameter: 0.055nm/K typical
02

TEC-Based Thermal Control

TEC-stabilized package configurations can provide active temperature adjustment. The TEC controller, sensor arrangement, heat path and package design must be evaluated together.

Package direction: TO-46 / TO-39 with TEC option
03

Atomic Frequency Locking

A TEC can help control the operating point, but it does not itself lock the laser to an atomic transition. Frequency locking requires an optical reference, detection path, feedback signal and control electronics.

System elements: vapor cell · photodetector · servo · reference

Do not confuse thermal stabilization with frequency locking. A TEC can stabilize temperature and help control wavelength drift. It does not independently provide an atomic frequency reference, narrow the free-running linewidth to a specified value or guarantee long-term clock stability.

System Integration

Typical Optical Architecture for Rubidium Atomic Clock & OPM Systems

The VCSEL is one component in a precision optical instrument. The complete design includes optical conditioning, the atomic vapor cell, photodetection, thermal management and electronic control.

01 · SOURCE795nm VCSELSingle-mode optical emission
02 · CONTROLCurrent / RF / TECBias, modulation and temperature
03 · OPTICSPolarization & BeamCollimation and polarization control
04 · ATOMSRb Vapor CellOptical pumping and resonance
05 · READOUTPhotodetector & ServoSignal readout and feedback

Atomic Clock Design Inputs

  • Rubidium isotope and target transition
  • CPT, optical pumping or alternative clock scheme
  • RF modulation frequency and required sideband structure
  • Laser frequency lock and long-term stability target
  • Optical power delivered to the vapor cell
  • Vapor-cell temperature and magnetic-field control

OPM Magnetometer Design Inputs

  • Rb isotope, cell geometry and operating regime
  • Optical pumping and probing configuration
  • Polarization state and optical power stability
  • Laser intensity and phase noise requirements
  • Magnetic shielding and package material constraints
  • TEC / driver magnetic interference and thermal noise

System-level performance—including clock stability, magnetometer sensitivity, bandwidth and drift—depends on the complete instrument design. It cannot be inferred from the VCSEL datasheet alone.

OEM Engineering Selection

How to Specify a 795nm VCSEL for an Atomic Clock or Magnetometer

Provide the atomic species, transition, system architecture and optical requirements first. This allows the laser source and package to be evaluated against the actual vapor-cell design.

Laser & Optical Requirements

  • Atomic species and isotope: 85Rb or 87Rb
  • Transition: D1 or D2
  • Required center wavelength and tuning range
  • Output power and power stability
  • Linewidth, SMSR and polarization requirements
  • FM bandwidth, modulation depth and RF drive
  • Beam divergence and optical coupling

Package & System Requirements

  • TO-46 or TO-39 package preference
  • TEC configuration and temperature-control range
  • Thermistor / temperature-sensor requirements
  • Magnetic compatibility and material restrictions
  • Vapor-cell geometry and optical path
  • Operating temperature and environmental conditions
  • Prototype quantity and annual production volume

Documents & Evaluation Items to Request

  • Full datasheet and LIV curves
  • Optical spectrum and linewidth test method
  • FM response and RF impedance data
  • Wavelength tuning versus current and temperature
  • Polarization and beam-profile data
  • Package drawing and pin definition
  • TEC configuration and thermal data
  • Magnetic material information if required by OPM design
Related Lumi Resources

Explore VCSEL Technology, Packaging and Laser Selection

Use these resources to understand the laser architecture and package choices behind wavelength-sensitive optical systems.

What Is a VCSEL?

Learn how vertical-cavity surface-emitting lasers work, how their resonator differs from edge-emitting devices and where VCSELs are used.

Read the VCSEL Guide →

DFB vs FP vs VCSEL

Compare laser architectures by spectral behavior, cavity design, modulation and application requirements.

Read the Architecture Guide →

SMD VCSEL vs TO-Can VCSEL

Understand how package format affects optical access, thermal path, PCB integration and system mechanics.

Read the Package Comparison →

Laser Diode Package Types

Review TO-can, butterfly, SMD and fiber-coupled formats for OEM optical systems.

Read the Package Guide →

Lumi VCSEL Laser Diodes

Browse Lumi's published 795nm, 850nm and 940nm VCSEL directions and compare current device configurations.

Explore VCSEL Products →

TO-Can Laser Diodes

Explore TO-package laser sources, including selected VCSEL, FP and DFB device directions.

Explore TO-Can Products →

Further technical reading: Application of VCSEL in Bio-Sensing Atomic Magnetometers reviews VCSEL requirements for atomic magnetometers, including wavelength matching, polarization and noise considerations. Key Technologies in Developing Chip-Scale Hot Atomic Devices for Precision Quantum Metrology reviews laser sources and integration challenges in chip-scale atomic systems.

Frequently Asked Questions

795nm VCSEL for Atomic Clock & OPM FAQ

Common questions about rubidium D1 wavelength selection, CPT modulation, magnetometer integration and Lumi's 795nm VCSEL.

Why is 795nm used in rubidium atomic clocks?

795nm is close to the rubidium D1 optical transition near 794.98nm. Rubidium CPT atomic-clock architectures use optical frequency components near this transition to interrogate the atoms in a vapor cell. The exact isotope, hyperfine transition and frequency-locking method must be defined by the system designer.

Can a 795nm VCSEL be used for an OPM magnetometer?

A 795nm source can address the rubidium D1 transition used in Rb-based optically pumped magnetometers. The complete source must also meet the system's optical power, polarization, intensity-noise, phase-noise, thermal and magnetic-compatibility requirements. Suitability should be confirmed with the actual vapor cell and magnetometer architecture.

What does the 3.4GHz FM modulation bandwidth mean?

Lumi's 795nm product specifies a minimum FM modulation bandwidth of 3.4GHz. This is relevant to evaluating VCSEL modulation for Rb CPT clock architectures, where modulation near 3.417GHz is commonly used. The specification alone does not guarantee a required modulation depth, sideband balance or clock performance.

Does the 795nm VCSEL include an atomic frequency lock?

No. The product is a VCSEL laser source. Atomic frequency locking requires a reference such as a rubidium vapor cell, optical detection, feedback electronics and a control loop. TEC stabilization can help control the operating temperature but is not an atomic frequency lock.

Is a 100MHz linewidth narrow enough for an atomic clock?

The published 100MHz value is the maximum spectral linewidth of the VCSEL device under its stated characterization. In a clock system, the effective optical frequency behavior depends on modulation, atomic-reference locking, feedback and noise. Customers should validate the free-running source and locked system against their required clock stability and resonance performance.

Does Lumi offer a non-magnetic TO-46 package for OPM?

The current Lumi product listing identifies TO-46 and TO-39 package options and TEC-stabilized configurations. It does not confirm a non-magnetic package or magnetic-material screening. OPM projects should specify the magnetic environment and request package-material review before design-in.

What is the typical output power of Lumi's 795nm VCSEL?

The product page specifies 0.13mW typical output power under the stated reference conditions. Confirm the optical power delivered to the vapor cell after coupling, polarization optics and other optical losses. If the system requires higher optical power, discuss the requirement with Lumi before selecting the device.

Does the TEC stabilize the laser frequency?

The TEC provides active thermal control and can help stabilize the laser operating temperature and wavelength. It does not independently provide an atomic frequency reference or guarantee a specified frequency-locking accuracy. The laser, temperature controller, current driver, optical reference and feedback loop must be evaluated together.

What should I include in an atomic-sensing VCSEL inquiry?

Provide the atomic species and isotope, D-line transition, target wavelength, required optical power, linewidth, polarization, modulation frequency and depth, package, TEC requirement, magnetic-material restrictions, vapor-cell configuration, sample quantity and target production volume.

Lumi 795nm VCSEL · OEM Optical Source

Developing a Rubidium Atomic Clock or OPM Magnetometer?

Share your Rb isotope, D1 transition, optical power, linewidth, modulation, polarization, package and thermal-control requirements. Lumi can review the published 795nm VCSEL and discuss TO-46 / TO-39 and TEC configuration options for your project.

has been added to your cart.
Checkout