Ethane Gas Sensing Laser Diodes

Ethane Detection · C₂H₆ · Laser Spectroscopy

Ethane Gas Sensing Laser Sources for TDLAS & OEM Analyzers

Explore near-infrared DFB laser source requirements for ethane (C₂H₆) detection in natural-gas analysis, mud-gas logging and dual-channel methane/ethane instruments. Lumi can review project requirements for a 1680 nm-class ethane laser source, while the exact absorption feature and laser tuning range are established during OEM evaluation.

Start with the C₂H₆ spectral target, not a wavelength label alone. Ethane bands near 1.68 µm require careful consideration of overlapping methane features, pressure, temperature and the optical receiver.

1680 nm-class DFB~1684 nm SpectroscopyCH₄ / C₂H₆ Dual GasOEM Optical Integration
Near-IR / Ethane Optical SensingC₂H₆
1680 nmLumi ethane DFB project direction
~1684 nmPublished ethane spectroscopy region
Spectral target ATarget B
Conceptual spectral illustration only. Neither curve nor marker is a measured C₂H₆ absorption spectrum or product tuning specification.
Explore Ethane Applications

From C₂H₆ Absorption to Laser Source Selection

Select a topic below to review wavelength requirements, optical architectures and matching component options.

Ethane / C₂H₆ Measurement

Why Measure Ethane Alongside Methane?

Ethane is a light hydrocarbon present in many natural-gas mixtures. Measuring C₂H₆ alongside CH₄ adds a composition-specific signal that methane-only monitoring cannot provide.

01

Gas Composition

Ethane concentration can support characterization of light hydrocarbon mixtures. In natural gas and process streams, the value of an ethane channel depends on the analyzer's full species coverage and calibration.

02

Mud-Gas Logging

C₂H₆ measurements can be correlated with CH₄, drilling depth and other mud-gas data. Changes in C1/C2 trends can support interpretation, but should not be used as universal standalone reservoir classifiers.

03

Dual-Gas Optical Analyzers

Dedicated wavelengths can support separate methane and ethane measurement channels in a single instrument. Cross-interference management, gas sampling and signal processing remain essential.

A two-species laser analyzer measures CH₄ and C₂H₆ channels; it does not automatically replace a full C1–C5 gas chromatograph or determine reservoir fluid type by itself.

Spectral Selection

1680 nm vs ~1684 nm: Which Ethane Laser Wavelength?

Near-infrared studies use different emission regions and specific tuning conditions. The nominal wavelength is only a starting point: the usable scan must reach the required ethane absorption structure under operating conditions.

Design point1680 nm-class DFB~1684 nm DFB
Role in this pageEthane DFB source direction for OEM project evaluationRegion used by published near-infrared C₂H₆ spectroscopic studies
Product statusConfiguration and availability confirmed by inquiryResearch wavelength target; request configuration feasibility
Absorption measurementRequires exact target feature, current scan and temperature window confirmationPublished studies report ethane absorption near 1.684 µm and 5937 cm⁻¹
InterferenceCheck CH₄ and other hydrocarbon overlap at the intended conditionsCheck nearby CH₄ absorption and background-gas effects
OEM information neededDesired absorption position, test current/temperature, output and packageExact feature, tune range, bandwidth, mode behavior and configuration

Engineering distinction: a product marked “1680 nm” does not automatically reach a desired “1684 nm” line. The required wavelength offset, tuning coefficients, allowed operating current/temperature and mode behavior must all be checked against a verified device specification.

Dual-Gas TDLAS Systems

How a Methane + Ethane Laser Analyzer Can Be Designed

A practical two-channel architecture uses separately controlled light sources for the selected CH₄ and C₂H₆ features, with optical detection and species-specific calibration.

CHANNEL 1 · CH₄

1653.7 nm Methane DFB

A published Lumi TEC-cooled DFB laser diode provides a methane-oriented source. The exact scan and gas response remain dependent on the analyzer's optical and control design.

CHANNEL 2 · C₂H₆

1680 nm-Class Ethane DFB Evaluation

The C₂H₆ source must be specified to reach the chosen ethane absorption feature. The available TO56 project data requires final model, test-condition and tunability confirmation before a commercial SKU is published.

01 / LASERSCH₄ + C₂H₆Two controlled wavelength channels
02 / OPTICSCoupling / RoutingCombine or separate optical paths
03 / GASMeasurement CellDefined path length, pressure and sample
04 / DETECTORCompatible ReceiverSpectral response and bandwidth verified
05 / DATASignal ProcessingSeparate calibration and gas outputs

Separate Laser Control

Each laser may require its own current driver, temperature-control loop, wavelength scan and operating-point characterization.

Shared or Separate Optics

Optical paths can be combined or kept independent. The correct choice depends on optical loss, alignment, modulation timing and channel cross-talk.

Species-Specific Calibration

CH₄ and C₂H₆ features should be calibrated for the intended gas matrix, pressure, temperature and signal-processing method.

Lumi Ethane Light Source Direction

1680 nm-Class Ethane DFB Laser: OEM Selection & Feasibility

For an ethane analyzer, we review the required absorption feature and the laser's measurable optical behavior before confirming a model and package. For a 1680 nm-class ethane source, our team can review the TO56 packaging direction and spectral requirements through a project-specific inquiry.

What to Confirm Before Selecting a C₂H₆ DFB

  • Exact ethane absorption region and required scan span
  • DFB center wavelength at a defined current and temperature
  • Current and temperature tuning coefficients and allowed limits
  • Optical output power at the specified operating point
  • Spectral linewidth, SMSR and mode-hop behavior
  • TO56 electrical pinout and thermal-control design
  • Free-space or fiber-coupled integration requirements
  • Prototype quantity and expected annual volume
OEM Project Direction

Ethane DFB · TO56 Candidate

A 1680 nm-class DFB in TO56 format can be discussed for ethane OEM projects. We confirm the available model, test conditions, required wavelength scan and package configuration against each application before quotation.

Target speciesEthane / C₂H₆
Nominal direction1680 nm-class
Candidate packageTO56
Available power / tune spanTo be confirmed
Ordering configurationConfirmed by inquiry

A 1680 nm-class source should not be assumed to match every ethane absorption feature. Exact spectral, electrical and packaging specifications are confirmed as part of the OEM evaluation.

Near-Infrared Reception

Photodetector Selection Near the 1.68 µm Ethane Band

Matching the detector to the laser wavelength is a separate engineering step. The receiver must provide useful responsivity at the exact operating wavelength with an appropriate noise, bandwidth and optical-power budget.

InGaAs PIN: Verify Response Near 1680–1684 nm

Lumi publishes a 900–1700 nm InGaAs PIN photodiode. The nominal response range includes the ethane region near 1680–1684 nm, but those wavelengths approach the long-wavelength end of the stated range. Its performance at this operating point should therefore be checked against the spectral-response curve and receiver circuit conditions.

  • Responsivity at the actual ethane laser wavelength
  • Optical signal level after gas-cell and coupling losses
  • Dark current, capacitance and temperature dependence
  • Required detector bandwidth and amplifier noise
  • Active area, package and optical alignment
  • Need for a detector with extended long-wavelength response

Do not infer 1684 nm responsivity from the headline “900–1700 nm” response range or from a responsivity value specified at a different wavelength.

Explore Lumi Photodiodes →
Ethane Gas Measurement Applications

Where an Ethane Laser Channel Can Add Value

A C₂H₆ optical channel is most useful when it serves a defined gas-composition or process-measurement requirement, rather than being selected as a generic leak detector.

01

Natural-Gas Composition

A targeted ethane measurement can complement methane analysis in natural-gas instruments. Interpretation depends on the complete hydrocarbon mixture and the instrument calibration.

02

Mud-Gas Logging

C₂H₆ concentration can be tracked against depth and CH₄ during wellsite evaluation. Representative gas extraction, sample conditioning and lag correction are essential.

03

Methane / Ethane Differentiation

Species-selective detection can support comparison between methane-dominant and ethane-containing gas samples where the spectral method is properly validated.

04

Hydrocarbon Process Analysis

Near-IR laser sources can be evaluated for targeted ethane measurement in conditioned process-gas streams, subject to sample pressure and background interference.

05

OEM Dual-Channel Analyzers

Instrument builders can develop separate C₁ and C₂ optical channels, with independently controlled sources and signal processing tailored to each species.

06

Research Spectroscopy

Research systems may use direct absorption spectroscopy, wavelength modulation spectroscopy or photoacoustic approaches. Source requirements vary by measurement principle.

Spectroscopy & Signal Processing

Optical Measurement Methods for C₂H₆

The optical source is only one part of the sensing method. The instrument design should distinguish direct absorption, wavelength modulation and photoacoustic approaches.

01

Direct Absorption Spectroscopy

The transmitted laser intensity is recorded while the source scans across a gas absorption feature. Accurate baselines and knowledge of the gas cell are essential.

02

Wavelength Modulation Spectroscopy

A modulated laser and harmonic signal processing can support ethane measurements. The modulation depth, scan center and interference behavior must be optimized.

03

Photoacoustic Spectroscopy

QEPAS research has demonstrated ethane measurement using suitable near-IR laser excitation. Such systems require a photoacoustic cell and acoustic detection architecture rather than a conventional transmission-only receiver.

Published research provides evidence of these measurement approaches but does not establish the performance of a Lumi laser or a complete Lumi ethane analyzer.

Optical & Mechanical Integration

TO-Can, Fiber Output and Thermal Control for an Ethane OEM Design

Packaging and optical interfaces should be selected after the ethane spectral requirement is confirmed. A 1680 nm-class project source is not automatically available in every package offered elsewhere in the laser diode portfolio.

01

Compact TO-Can Source

The project file identifies a TO56 ethane DFB direction. Integrators should confirm pinout, mechanical drawing, electrical limits and any thermal-control components before board design.

02

Fiber-Coupled Output

Fiber delivery may help route laser light to a separate optical cell. For ethane projects, the wavelength, optical power, fiber type and connector availability need explicit confirmation.

03

Temperature & Driver Control

Gas spectroscopy requires control of laser wavelength through the drive and thermal environment. The usable tuning span and stability must be verified for the selected ethane device.

Request an OEM Ethane Source

Ethane Laser Diode RFQ Checklist

Share the details below so we can evaluate the optical requirement, candidate configuration and feasibility of the proposed ethane channel.

RequirementInformation to provideWhy it matters
Target gasEthane C₂H₆ alone or CH₄ + C₂H₆Defines single- or dual-species design
Absorption featureCenter line / wavenumber / reference spectrumDetermines wavelength and scan requirement
Nominal wavelength1680 nm-class, ~1684 nm or other targetPrevents an incorrect center-wavelength assumption
Laser tuningRequired current and temperature scanConfirms coverage of selected absorption feature
Optical outputPower at the laser or after the fiberSupports optical power budget
Spectral performanceSMSR, linewidth, mode-hop toleranceSupports wavelength-selective measurement
PackageTO56 or preferred format and dimensionsDefines mechanical and electrical integration
Output interfaceFree-space / SM fiber / connectorMatches optical cell or probe head
Operating conditionsTemperature, pressure, gas matrix, concentrationSupports interference and calibration evaluation
Detection circuitReceiver spectral response and amplifier needsConfirms 1.68 µm detector suitability
Project volumeSamples, target timeline, annual demandGuides sourcing and configuration review
Technical Resources & Related Components

Continue with Methane, TDLAS and Near-IR Detection

Use these published Lumi pages and external research resources to refine a proposed ethane analyzer design.

Methane & Ethane DFB for Mud Gas Logging

How methane and ethane optical channels can support depth-related gas analysis and what changes in C1/C2 trends mean.

TDLAS Gas Sensing

Understand DFB source selection, gas absorption, optical paths and OEM analyzer architecture.

Methane Laser Diodes

Review Lumi's 1650.9 nm heating-type and 1653.7 nm TEC-cooled methane DFB products.

TDLAS Wavelength Selection

Choose wavelength, tuning span and spectral characteristics from the gas absorption target.

Near-IR Photodiodes

Review detector spectral range, responsivity and receiver design constraints near the long-wavelength response edge.

Gas Sensing Applications

Find the broader gas sensing application center, related DFB families and optical integration directions.

Further reading: Research on near-infrared CH₄/C₂H₆ dual-gas TDLAS and ethane photoacoustic sensing provides examples of 1680 nm-class and ~1684 nm optical approaches. Published system results apply to those experimental systems, not to Lumi components.

Frequently Asked Questions

Ethane Gas Sensing Laser Diode FAQ

Practical answers about the C₂H₆ absorption region, DFB laser sourcing and dual-gas analyzer design.

What wavelength is used for ethane TDLAS gas sensing?

Near-infrared ethane sensing research includes 1680 nm-class DFB sources and studies around 1684 nm. The correct choice is the wavelength and tuning span that cover the selected ethane absorption feature in the intended gas matrix and operating conditions.

Can a 1680 nm DFB laser reach a 1684 nm ethane absorption feature?

Not necessarily. The nominal center wavelength does not define the full tuning range. Laser current tuning, temperature tuning, allowable operating conditions and single-mode behavior must all be verified using the actual device specification.

Does Lumi have a published 1684 nm ethane DFB product?

We evaluate 1680 nm-class ethane DFB requirements on a project basis. Please share the target absorption feature and desired tuning window so we can confirm the wavelength, package and supply configuration. A standard 1684 nm SKU should not be assumed without confirmation.

Why measure ethane together with methane?

Methane and ethane are different hydrocarbon species. An ethane channel adds compositional information to methane measurements, particularly in natural-gas analysis and mud-gas logging. Interpretation must account for the complete sample and measurement process.

Can one laser measure methane and ethane?

Research has demonstrated single-laser dual-gas schemes near 1684 nm using specially selected absorption features and signal processing. Many OEM implementations instead use separate wavelength channels. The best architecture depends on the target transitions, tuning capability and interference constraints.

Can the Lumi 900–1700 nm InGaAs photodiode receive an ethane laser?

The stated response range includes wavelengths around 1680–1684 nm, but they are near the long-wavelength end of the range. Verify responsivity at the exact wavelength, dark current, capacitance, bandwidth and the full receiver signal-to-noise budget before choosing the detector.

Can a dual-gas TDLAS analyzer replace gas chromatography?

A two-species laser system provides targeted CH₄ and C₂H₆ measurements. It does not automatically provide full C1–C5 composition or replace every function of a gas chromatograph. Method selection depends on the analyzer specification.

Does laser optical power determine the ethane detection limit?

No. A detection limit depends on absorption strength, path length, optical losses, source stability, receiver noise, electronics, spectral interference, calibration and gas sample conditions.

What should I include in an ethane laser diode inquiry?

Provide your target ethane absorption feature, wavelength or wavenumber, tuning span, optical output, laser architecture, package, thermal-control needs, gas conditions, detector response and expected sample and production quantities.

Lumi Ethane Sensing OEM Support

Developing an Ethane or Dual-Gas TDLAS Analyzer?

Share the selected C₂H₆ absorption region, tuning range, source power, package, thermal-control and detector requirements. We can review the ethane laser sourcing direction and related methane or optical detection components for your OEM project.

has been added to your cart.
Checkout